Choosing an injection molding machine by product weight alone is a common and costly mistake.

The correct machine must provide enough clamping force, injection capacity, plasticizing capacity and mold space. It must also meet the product’s requirements for injection pressure, injection speed, cycle time and production stability.

This guide explains how to determine the right injection molding machine size using the product drawing, plastic material and mold specifications.

Quick Answer: What Size Injection Molding Machine Do I Need?

To select an injection molding machine, check these five factors:

  1. Required clamping force
  2. Total shot weight
  3. Mold dimensions and tie-bar spacing
  4. Mold thickness and opening stroke
  5. Required injection pressure and speed

A suitable machine must pass all five checks. Meeting only the shot-weight requirement does not mean that the machine can operate the mold safely.

Injection molding machine tonnage and shot size calculation guide

1. Calculate the Required Clamping Force

Clamping force keeps the mold closed while molten plastic is injected into the cavities.

If the clamping force is too low, the mold may open slightly during injection, causing flash, unstable dimensions and possible mold damage.

A practical calculation is:

Required clamping force = Projected area × Estimated cavity pressure × Safety factor

When projected area is measured in square centimeters and cavity pressure in kilograms per square centimeter:

Clamping force (tons) = Projected area (cm²) × Cavity pressure (kg/cm²) ÷ 1,000 × Safety factor

A safety factor of approximately 1.1 to 1.2 is commonly used for preliminary machine selection. The final value should be confirmed according to the part geometry, material, flow length, wall thickness, gate design and molding parameters.

What Is Projected Area?

Projected area is the visible area of the molded part when viewed in the mold-closing direction.

For a multi-cavity mold, include:

  • Projected area of every cavity
  • Projected area of the runner system
  • Any additional area exposed to cavity pressure

For example, if one part has a projected area of 150 cm² and the mold has four cavities:

Total part area = 150 × 4 = 600 cm²

The runner area must then be added before calculating the clamping force.

Why Material and Part Design Matter

The same projected area does not always require the same machine tonnage.

Higher clamping force may be needed for:

  • Thin-wall containers
  • Long flow paths
  • Small gates
  • High-viscosity plastics
  • Glass-fiber-reinforced materials
  • High injection-speed applications
  • Products with large projected areas

A relatively lower cavity pressure may be possible for thick, simple products made from easy-flow materials. However, the mold flow and actual production conditions should always be considered.

2. Calculate the Required Shot Size

The machine must inject enough molten plastic to fill all cavities and the runner system while maintaining a reasonable reserve.

Calculate the total shot weight as follows:

Total shot weight = Weight of all molded parts + Runner weight

Example:

  • Product weight: 120 g
  • Number of cavities: 2
  • Estimated cold-runner weight: 25 g

The total shot weight is:

120 × 2 + 25 = 265 g

Do not select a machine whose maximum theoretical shot capacity is exactly 265 g.

For stable production, the actual shot normally should stay within a practical portion of the machine’s available injection capacity. The preferred range depends on the resin, screw design, residence time and process conditions.

An excessively large injection unit can also create problems. When the shot is too small compared with the barrel capacity, the material may remain inside the barrel too long and degrade.

3. Do Not Compare Shot Weight Without Checking the Resin

Machine specifications are often stated using polystyrene, commonly shown as “PS shot weight.”

The actual shot capacity changes with the density of the plastic being processed.

A machine listed with a 500 g PS shot weight does not necessarily inject 500 g of PP, PE, PA or PC under identical conditions. A density conversion and processing allowance are required.

When requesting a machine recommendation, tell the supplier the exact material, including:

  • PP, HDPE, ABS, PC, PA or other resin
  • Virgin or recycled material
  • Filler percentage
  • Glass-fiber percentage
  • Flame-retardant or other additives

This information also helps the supplier select a suitable screw design and wear-resistant material.

4. Check Mold Dimensions and Tie-Bar Spacing

Even if the tonnage and shot capacity are sufficient, the mold may not physically fit inside the machine.

Compare the mold dimensions with:

  • Horizontal tie-bar distance
  • Vertical tie-bar distance
  • Platen dimensions
  • Locating-ring diameter
  • Nozzle position
  • Mold mounting-hole pattern

The mold should fit safely between the tie bars with enough installation clearance.

If a mold is wider than the tie-bar spacing, ask whether it can be installed from the side. Side loading is only possible when the factory layout, lifting equipment and machine structure allow it.

5. Check Minimum and Maximum Mold Thickness

Every injection molding machine has a permitted mold-height range.

Confirm that the mold thickness is:

  • Greater than the machine’s minimum mold thickness
  • Lower than the machine’s maximum mold thickness

If the mold is too thin, additional support plates may sometimes be used, but this should be evaluated carefully. If the mold is too thick, the clamping unit may not close or provide the required opening movement.

6. Check Opening Stroke and Daylight

The mold must open far enough for the molded product and runner to be removed.

Check:

  • Product depth
  • Core height
  • Required ejector movement
  • Robot take-out clearance
  • Mold opening distance
  • Maximum daylight of the machine

Deep products such as buckets, crates, storage boxes and automotive parts usually require more opening stroke than flat products.

For automated production, allow sufficient space for the robot gripper or EOAT to enter and remove the product safely.

7. Check Ejector Stroke and Ejector Force

A large or deep product may need a longer ejector stroke. Multi-cavity molds and products with strong core adhesion may require higher ejector force.

Confirm:

  • Required ejector stroke
  • Ejector-rod position
  • Number of ejector rods
  • Required ejector force
  • Whether hydraulic core pulling is needed

These requirements should be checked before the machine is ordered—not after the mold arrives at the factory.

8. Check Injection Pressure and Injection Speed

Standard products and thin-wall products require different injection performance.

High injection speed is particularly important for:

  • Thin-wall food containers
  • Disposable cups
  • Lids
  • Cutlery
  • Packaging products
  • Long-flow-path components

Molten plastic begins cooling immediately after entering the mold. If the filling speed is too slow, short shots, flow marks and weak weld lines may occur.

For thin-wall production, machine selection should consider injection speed, injection acceleration, injection pressure, screw diameter and the response speed of the control system—not only clamping tonnage.

9. Check Plasticizing Capacity and Production Cycle

Shot capacity tells you how much the machine can inject. Plasticizing capacity tells you how quickly the machine can melt and prepare material for the next cycle.

This distinction becomes important when producing:

  • Heavy parts
  • Multi-cavity products
  • Products with short cycle times
  • High-output packaging products
  • Parts made from materials requiring special screw designs

If plasticizing takes longer than mold cooling and part removal, it becomes the production bottleneck.

Injection Molding Machine Selection Example

Assume a buyer wants to produce a four-cavity PP component.

Available information:

  • Part weight: 80 g
  • Number of cavities: 4
  • Runner weight: 30 g
  • Total projected area: 520 cm²
  • Mold size: 720 × 650 × 580 mm
  • Material: PP

The total shot weight is:

80 × 4 + 30 = 350 g

The next steps are:

  1. Estimate the appropriate cavity pressure for the part and PP grade.
  2. Multiply the projected area by the estimated cavity pressure.
  3. Add a suitable safety factor.
  4. Confirm that the machine’s actual PP shot capacity covers 350 g.
  5. Check the mold against the tie-bar spacing and platen dimensions.
  6. Confirm mold thickness, opening stroke and ejector requirements.
  7. Evaluate the required production cycle and plasticizing capacity.

This example shows why a machine cannot be selected from product weight alone.

Information to Send When Requesting a Machine Recommendation

For an accurate injection molding machine selection, send:

  • Product photos
  • 2D or 3D product drawing
  • Product dimensions
  • Product weight
  • Plastic material and grade
  • Number of mold cavities
  • Runner type: cold runner or hot runner
  • Mold dimensions
  • Mold weight
  • Minimum mold thickness
  • Required opening stroke
  • Core-pulling requirements
  • Target cycle time
  • Required hourly or annual output
  • Available factory voltage and frequency
  • Country of installation

If the mold already exists, also provide its nameplate and complete mold drawing.

Common Machine Selection Mistakes

Choosing the Machine Only by Tonnage

Two machines with the same clamping force can have different injection units, tie-bar spacing and opening strokes.

Choosing the Machine Only by Shot Weight

The mold may require more clamping force or may not fit between the tie bars.

Ignoring the Runner Weight

Cold-runner material can represent a significant part of the total shot.

Using PS Shot Weight as the Capacity for Every Resin

Actual capacity changes with material density and processing conditions.

Ignoring Future Products

A slightly more flexible machine may accommodate future molds, but oversizing too much can increase investment and energy use. Selection should balance current and expected production.

Frequently Asked Questions

Is a larger injection molding machine always better?

No. An oversized machine generally costs more, occupies more space and consumes more energy. An excessively large injection unit can also increase resin residence time and material degradation.

Can product weight determine machine tonnage?

No. Product weight helps determine shot capacity, while projected area and cavity pressure determine the required clamping force.

How much extra shot capacity should a machine have?

The machine should have a reasonable processing reserve, but the exact range depends on the resin, shot volume, screw diameter and permitted residence time. Ask the machine supplier to calculate the actual capacity for your material.

What information is most important when choosing a machine?

The most important information includes projected area, total shot weight, material, mold size, mold thickness, opening requirements and target cycle time.

Need Help Selecting an Injection Molding Machine?

DAYA supplies servo injection molding machines, high-speed injection molding machines and complete plastic production solutions.

Send us your product drawing, product weight, material, mold specifications and production target. Our team can evaluate the required clamping force, injection capacity, mold compatibility and auxiliary equipment.

Request an Injection Molding Machine Recommendation