Servo Motors for Injection Molding Machines

Loss of pressure, unstable speed, encoder alarms, excessive motor temperature, or abnormal vibration can stop a servo-hydraulic injection molding machine without warning. The servo motor drives the hydraulic pump according to real-time flow and pressure demand. DAYA provides replacement, repair, and compatibility support for permanent-magnet synchronous and AC servo motors used in energy-saving injection molding machines, including motor-to-drive matching and encoder verification.

Injection molding machine servo motor replacement and repair


1. Dynamic Hydraulic Power with Lower Energy Consumption

Unlike a conventional motor running continuously at fixed speed, a correctly controlled servo motor accelerates, decelerates, and holds speed as the molding cycle requires. This improves response, lowers idle energy use, and reduces hydraulic oil heating and system noise.

Common brands and machine applications we can support include:

  • Inovance, Hilectro, Phase, Huichuan and common Chinese servo-hydraulic systems

  • Yaskawa, Mitsubishi, Siemens, Bosch Rexroth and compatible industrial servo platforms

  • Motors used on DAYA, Haitian, Yizumi, Chen Hsong, Borche, LK and retrofit projects

  • Repair options for stator, bearings, encoder, cooling fan, connectors, and feedback cable when technically economical

Compatibility is confirmed from the original model and application data. Brand names are used for identification and do not imply that parts with a similar appearance are automatically interchangeable.


2. Main Types, Configurations, and Selection Points

The correct configuration depends on the machine circuit and operating duty. The table below summarizes the most common options.

Type / ConfigurationTypical ApplicationCritical Selection Details
Permanent-magnet synchronous motorMain pump drive in energy-saving hydraulic pressesRated power/torque, speed, encoder, cooling
AC servo motorClosed-loop motion or pump applicationsDrive family, feedback protocol, flange/shaft
Servo pump motor assemblyMatched motor, coupling, and hydraulic pumpPump displacement, rotation, alignment
Repaired original motorMaintaining mechanical and electrical compatibilityInsulation, rotor magnet, encoder calibration

Selection note: Never rely only on the front appearance or a shortened model number. Small differences in voltage, signal logic, pressure, flow, connector, dimensions, firmware, or material can prevent installation or create a new fault.


3. When Replacement or Technical Inspection Is Needed

A replacement should be considered when one or more of the following conditions are confirmed:

  • Overcurrent, overload, encoder, overtemperature, or phase-loss alarm

  • Motor cannot start, rotates in the wrong direction, or fails under pressure demand

  • Unusual bearing noise, vibration, coupling wear, or shaft damage

  • Reduced torque, unstable pump speed, or repeated drive trips during injection

  • Oil contamination or water ingress reaches the motor, cable, or connector

Before replacing the component, verify the surrounding circuit. Wiring, connectors, power quality, contamination, cooling, lubrication, mechanical alignment, controller parameters, and downstream loads can produce the same symptom. Correct diagnosis avoids repeated failure of the new part.


4. How to Identify the Correct Replacement

For a fast and accurate quotation, please provide the following information:

  1. 1. Complete motor nameplate and matching servo-drive model

  2. 2. Rated power, voltage, current, speed, torque, and cooling method

  3. 3. Encoder type, resolution, feedback protocol, connector and cable details

  4. 4. Flange dimensions, shaft diameter/length/key, and mounting orientation

  5. 5. Hydraulic pump model, coupling details, rotation direction, machine brand/model, and alarm history

If the nameplate is missing or unreadable, send multiple high-resolution photos with a ruler beside the component, mark every connector and port, and provide the machine brand, model, serial number, year, and the function controlled by the part.


5. Supply, Compatibility, and Service Options

Motor replacement is treated as a system-matching task, not a nameplate-only purchase. We check motor, drive, encoder, pump, mechanical interface, and control parameters together and advise whether replacement, repair, or a matched upgrade is the safer route.

  • Original or OEM-specified replacement when the exact part remains available.

  • Compatible industrial replacement after mechanical, electrical, hydraulic, and control details are checked.

  • Repair or refurbishment assessment for selected high-value components.

  • Matched upgrade solution when the original model is obsolete or repeatedly unreliable.

Where useful, we can supply related cables, connectors, sockets, seals, fittings, brackets, filters, sensors, or installation accessories together to reduce downtime caused by missing small parts.


6. Frequently Asked Questions

Can a servo motor with the same kW rating replace the original?

Not automatically. Rated speed and torque, encoder protocol, electrical constants, flange, shaft, cooling, drive firmware, and parameter range must also be compatible.

Should the motor and servo drive be replaced together?

If the original motor is available and the drive is healthy, a matched motor replacement may be sufficient. For obsolete systems or repeated faults, a complete matched motor-and-drive solution may reduce commissioning risk.


7. Request a Fast Parts Quotation

Send the original part model, clear nameplate photos, machine information, dimensions, and fault description. DAYA will review the application and recommend the most practical route: an exact replacement, a compatible alternative, repair support, or a coordinated upgrade.

Explore our injection molding machine spare parts and consumables, review more maintenance and troubleshooting resources, or contact DAYA for a quotation.

Reduce troubleshooting time and avoid an incorrect replacement—send us the part photos and machine details today.